|Simliar Brand:||Polyken,Denso,Altene||Film Layer:||Polyethylene|
|Adhesive Layer:||Butyl Rubber||Test Report:||SGS,DVGW,AWWA|
|Main Market:||Iran,UAE,Iraq,Kuwait,Turkey,Egypt,Libya,Ukraine,Russia,Uzbekistan,India, Australia,Indonesia,Kazakhstan,Ecuador,Venezuela,Bolivia,Argentina, Uruguay,Malaysia And So On.||Color:||Black,yellow|
|Standards:||ASTM D 1000, EN 12068||Thickness:||0.38 Mm，0.50 Mm,0.75 Mm，0.9 Mm,1.65 Mm|
pipe wrap insulation tape,
pipe wrapping tape
Yellow Color Pipe Wrap Tape , Outer Mechanical Wrapping corrosion protection tape For Pipes
YELLOW COLOR PIPE WRAPPING TAPE is Cold applied tape coating system for corrosion protection of Oil, Gas, Petrochemical, and Waste Water underground or overhead pipelines.
This product has been made by a special processing of butyl rubber to P.E. Its durability is strong and electric corrosion can be prevented. The pipe can be semi-permanently preserved which has an excellent effect on its corrosion resistance. It has a permanent and continuous adhesion effect, this outstanding combination of butyl rubber adhesion and P.E, make good weather resistance, outstanding electric and chemical characteristics and good workability for ease in both manual and machine work.
1) Anti-corrosion WRAPPING of water pipe, gas pipe, oil pipe, etc
2) Anti-corrosion of electric wire, voltage and communication cable
3) Anti-corrosion of pipe in chemical factories having severe moisture and corrosion
4) Anti-corrosion of various pipe lines
Application temperature : -34°C ~ 71°C
Service temperature : -34°C ~ 85°C
Primer: Primer increases tape adhesiveness.
|Total thickness||ASTM D 1000||25.0 mil (0.635mm)|
|Backing thickness||ASTM D 1000||20.0 mil (0.51 mm)|
|Adhesive thickness||ASTM D 1000||5.0mil (0.125 mm)|
|Width||-||2’’- 32’’ (50 -800 mm)|
|Length||-||100’ -800 ‘(30 -240 m)|
|Backing colour||-||White or black|
|Tensile strength||ASTM D 1000||75 N/ cm|
|Elongation||ASTM D 1000||400 %|
|Peel Adhesion to inner-layer tape||ASTM D 1000||5 N/cm|
|Cathodic Disbandment||ASTM G8||0.25 in radius 6.4 mm|
|Dielectric Strength||ASTM D 149||40 Kv|
|Volume Resistivity||ASTM D 257||2.2x1012 ohm.cm|
|Water Absorptivity||ASTM D 570||0.1 %|
|Water Vapor Transmission Rate (24h)||ASTM F1249||0.01g/100sq in/24h|
|Application Temperature||-||14℉-140℉ (-10 ℃ - 60 ℃)|
|Max Service Temperature||-||-40℉-1℉ (- 40 ℃ - 90℃)|
How to use?
1) Pipe surface processing
thoroughly clean the surface of the pipe by removing all foreign material.
Completely remove any sharp projections from the area of the weld.
Remove all rust and/or other impurities using a steel brush.
2) Apply primer
Before application, shake or mix primer thoroughly.
Because it is highly volatile, make sure it is securely sealed after use.
Because it contains inflammable solvents, use caution when working near any open flames.
To obtain best results, apply primer in a temperature range of 0°C~25°C and for storage a
Temperature of -20°C~35°C is best.
Proper volume of primer is 100g per 1m².
When primer is applied and PE anti-corrosive tape is used, it is recommended to apply the
tape within a short time after the primer is completely dry.
JINING XUNDA PIPE COATING MATEIRIALS CO.LTD INFORMATION:
Contact Person: Angelina Meng
Tel: + 8618853777531