|
Product Details:
|
| Backing: | POLYETHYLENE | Adhesive: | Butyl Rubber |
|---|---|---|---|
| Use: | Pipe Corrosion Protection Insulation | Color: | White |
| Available Roll Size (width X Length): | 2" To 32" X 50’ To 800’ | Standard: | DIN 30672,ASTM D1000,EN 12068, AWWA C 209 & 214 |
| Similar Brand: | TAK,Polyken,DENSO,ALTENE | Service Life: | More Than 30 Years For The Undeground Pipeline |
| High Light: | insulation tape for pipes,black insulation tape |
||
White Color Insulation Tape For Pipes Butyl Rubber Adhesive
Product Description:
XUNDA T 200 series outer wrap tape is produced through extruding the composite anti corrosion materials. The adhesive layer is attached to the polyethylene film backing through thermal compounding. The anti corrosion system is comprised of primer, anti corrosion adhesive tape (inner tape) and protective tape (outer tape)
The outer wrap tape always called Mechanical tape,outer tape,outer wrap tape,outer layer tape,outerwrap tape.The backing is more thicker with a few adhesive .The color is White.
Usage:
The XUNDA-T200 series is Cold applied tape coating system for corrosion protection of Oil, Gas, Petrochemical, and Waste Water underground or overhead pipelines. The outer-layer tape backing shall be compounded so that it will be resistance to outdoor weathering.
It also provide protection to the inner layer from damage during storage, transportation, installation and throughout the lifetime of the pipeline
Features & Benefits
Featuring excellent insulativity
Resistant to UV
Easily applied with no special equipment
Compatible with common pipe coatings
Excellent resistance to cathodic disbonding
Good Mechanical protective effect
High mechanical strength
Small water absorption
Long service lifetime
Good resistance to impact and ageing
The outer wrap tape can be used in the construction conveniently with safety and no pollution
The outer wrap tape is widely applied in many areas with high efficiency.
Order size choice:
| Tape thickness | 15 mils(0.38 mm),20 mils (0.50 mm)25 mils (0.635 mm) 30mils(0.762mm) |
| Tape color | Black (BLK), White (WHT), Blue (BLU),GREEN(GRN) |
| Tape width | 1" (25 mm), 2" (50 mm), 4" (100 mm), 6"(150 mm),9’’(230 mm)12 ‘’(300 mm) |
| Tape roll length | 100ft,200ft,400ft,600ft,800ft |
| Tape core diameter | 1.5" (38 mm), 3" (75 mm) |
Technical data sheet
XUNDA-T 265 = Polyken 955-25/Altene 122-25
|
Physical Properties |
Test Method |
Typical Value |
| Total thickness | ASTM D 1000 | 25.0 mil (0.635mm) |
| Backing thickness | ASTM D 1000 | 20.0 mil (0.51 mm) |
| Adhesive thickness | ASTM D 1000 | 5.0mil (0.125 mm) |
| Width | - | 2’’- 32’’ (50 -800 mm) |
| Length | - | 100’ -800 ‘(30 -240 m) |
| Backing colour | - | White or black |
| Tensile strength | ASTM D 1000 | 75 N/ cm |
| Elongation | ASTM D 1000 | 400 % |
| Peel Adhesion to inner-layer tape | ASTM D 1000 | 5 N/cm |
| Cathodic Disbandment | ASTM G8 | 0.25 in radius 6.4 mm |
| Dielectric Strength | ASTM D 149 | 40 Kv |
| Volume Resistivity | ASTM D 257 | 2.2x1012 ohm.cm |
| Water Absorptivity | ASTM D 570 | 0.1 % |
| Water Vapor Transmission Rate (24h) | ASTM F1249 | 0.01g/100sq in/24h |
| UV resistance | - | Excellent |
| Application Temperature | - | 14℉-140℉ (-10 ℃ - 60 ℃) |
| Max Service Temperature | - | -40℉-1℉ (- 40 ℃ - 90℃) |
How to store the outer wrap protection tape ?
The coating materials shall be stored in a clean, dry area
All materials shall be delivered to the jobsite in sealed and labelled containers and
shall be stored in a location that is protected from the elements, well ventilated and free from excessive heat, open flame, or other sources of ignition. Coating materials subject to freeze shall be stored in a heated area.
The materials storerooms shall be appropriately ventilated and shall comply with applicable law provisions on safety and fire prevention.
Tape stored at jobsites or material yards shall be kept dry and under cover and never exposed to direct sunlight. Rolls shall not be stacked more than four (4) tiers high and never directly on the ground or on irregular surfaces. The cores of stored tape rolls shall be vertical. Rolls shall not be thrown or dropped. Hooks or other sharp handling devices shall not be used. Tape shall not be stored in contact with protrusions capable of puncturing the material. Rolls or equipment shall not be piled on top of or against stored tape.
JINING XUNDA PIPE COATING MATERIALS CO.,LTD
Contact Person: Angelina Meng
Tel: + 8618853777531
